How to clean maf

After cleaning the MAF sensor allow it to dry completely for a few minutes. Some mass sensor a located at the back of your air filter.

Place the sensor on.

How to clean maf. Carefully remove the sensor from the air duct and disconnect the electrical connector. Spray 10 to 15 spurts of the mass air flower cleaner onto the wire or plate. Dont scrub the parts.

You may break the wire or damage the plate. Allow the MAF sensor to dry completely before reinstalling it in the air duct. How to Clean a Mass Air Flow Sensor 1.

Turn the engine off remove the keys from the ignition and let the engine cool. Locate the mass air flow sensor by. With the sensor unplugged loosen the clamps and any brackets holding it in place.

Slide the sensor assembly away. Place the sensor on. Attach the straw to your spray can and begin to apply the MAF cleaner.

You should hit every part of the sensor with 10-15 bursts of cleaner. DO NOT let the straw touch the sensor. At no time should anything touch the actual sensor or you risk damaging it.

How to Clean a MAF Sensor. Step 1 - Locate the MAF. The first thing to do is to open the hood and find the location of your MAF.

It is most like in a black plastic box thats. Step 2 - Remove the MAF. Step 3 - Soak the MAF in Alcohol.

Step 4 - Dry the MAF. Step 5 - Replace the MAF. Mass air flow sensor cleaning.

Never Do This When Cleaning Your Mass Air Flow Sensor DIY with Scotty Kilmer. How to clean mass air flow sensor in your car. Swish the baggie around so the alcohol can get into every part of the MAF.

Leave the MAF in the baggie for about 20 minutes or so to make sure it really cleans all the dirt and debris out of the critical components. Step 5 Pull the MAF out of the bag and place in a dry area on a towel for at least 45 minutes. How to clean the MAF mass air flow sensor in a 2000 Toyota Yaris 10 petrol.

Thanks for watching please comment like and subscribe. All of my uploaded. Spray 10-15 bursts of CRC MAF Cleaner on all parts of the sensor.

Spray all sides of the sensor and housing including the connectors. Dont forget to spray the terminals. Reinstall the sensor into the car and allow a few minutes for the chemicals to evaporate before starting the engine.

Spray a small amount of the sensor cleaner solution into a small clean cup. Soak the small brush in the cleaning solution. Use the brush to wipe dirt and debris from the wire s.

After cleaning the MAF sensor allow it to dry completely for a few minutes. How to Clean a MAF With Alcohol Step 1. Locate the mass air flow sensor on your vehicle which will be under the hood.

Most cars MAFs can be found. Remove the MAF sensor from the vehicle. Check the cars service manual for directions on how to remove the piece.

What Do I Use To Clean The MAF Sensor. We cant just use any type of solvent to clean the MAF sensor with. Here are a couple of very important guidelines on what to use.

An Electronics Spray Cleaner can be used. You can buy it at your local auto parts store AutoZone Pepboys OReilly etc. First it is recommended to clean it with a rubbing alcohol plastic bag.

Lets put your MAF inside the bag move it around so that the alcohol can cover the MAF surfaces. Then removing grime and dirt is easy peasy. Another noteworthy solution is to clean the sensor with a MAF mass air flow sensor cleaner.

To clean the mass airflow sensor first you need to identify the MAF sensor beneath the hood of your car. Some mass sensor a located at the back of your air filter. Next you have to take out the mass air flow sensor and to do this you need to consult with you owners manual for instruction on how to take it out.

To clean the MAF I used acetone and cotton buds. Acetone does not leave any residue behind when it dries and it does not effect electrical components so it is perfect for this use. Nothing special about the cotton buds.

Mass Airflow Sensor cleaning is very straight forward simply soak the end of the cotton buds and wipe the wires. You can also use MAF Cleaner or brake cleaner but its more messy. If using the canned cleaners juts spray the MAF from a little distance aways and then let it dry.

Using a q Tip just dip the Q tip into the rubbing alcohol and then proceed to rub it up and down the metal pole in the sensor. Set the MAF on a paper towel or clean shop rag. Follow the directions on the can to spray the solvent on the MAF.

Be careful that the spray tube or other things do not bump the MAF. Again the wires are fragile.