How to fix a seat belt retractor

The cover is a small door and is located below the shoulder mount of the seat belt. Clean the seat belt retractor.

How Do You Fix a Seat Belt That Does Not Retract.

How to fix a seat belt retractor. This video demonstrates the process of fixing the slow to retract seat beltPart 2 of 2Stuff I commonly use in these videosMilwaukee Ratchet. Today I will show you how to fix your stuck or slowly reclining seat belts with regular you have laying around at home0000 intro0010 the problem0056 fixi. Here is how to fix the seat belt retractor when it is locked.

First pull the webbing out of the seat belt completely and then give it a yank to undo the locked belt. If this does not work for you take the retractor out of the vehicle. Then using a screwdriver you can manually spin the spool.

BEST WAYS TO FIX A SLOW RETRACTING SEAT BELT 1. Lubricate the plastic loop through which the seat belt goes through. Clean the seat belt fabric.

Without dismantling the belt mechanism. Clean the seat belt retractor. In this option youll have to dismantle trim panels and clean the.

Seat Belt Retractor Repair Instructions Step 1. Remove the seat belt retractor mounting screws in the cover. The cover is directly below the shoulder mount of.

Place a pair of adjustable pliers on the retractor mounting bolt. Turn the pliers counterclockwise to loosen the. Video showing you an easy way to repair a stuck seat belt that wont retract rewind back into the automobile.

The tools you will need are a screwdriver rat. If you have ever had a stuck seat belt retractor this video will show you how to unlock the retractor to get the belt moving again. Well its easy as pie.

All you have to take a towel small bucket or any container detergent and warm water. Put the warm water into the bucket and add the detergent to it. Next what you are going to do is to lock the seat belt with the help of a clip and put the rest of the belt into the bucket of warm water and detergent.

How Do You Fix a Seat Belt That Does Not Retract. Check the seat belt mechanismsFind your car manual and look up the seat belt section. If your seat belts use.

Remove the seat belt retractorPull the casing off the seat belt retraction system. If you are working on an exterior. Clean the seat.

To fix a locked seat belt retractor pull the webbing out of the seat belt completely and then give it a yank to undo the locked belt. If this does not work for you take the retractor out of the vehicle. Then using a screwdriver you can manually spin the spool.

This slowly retracts the seat belt webbing back into the mechanism. The seat belt retractor may be broken and needs to be replaced. The seat belt retractor is the part where the seat belt rolls in.

This is what pulls the seat belt back. The proper way to fix a broken seat belt retractor is to replace the retractor and belt with a new set. Untangle the seatbelt if there are any jams in it.

In addition if there are any objects stuck within the belt loop or the bottom portion of the belt loop remove them with either your fingers or by using needle nose pliers. Allow the seatbelt to roll back into place. Test the belt to make sure it releases and locks into place normally.

A seat belt retractor repair is the process of unlocking the locked seat belt rebuilding the mechanism replacing the gas charge and installing a new sensor. Because these are vital safety components this is done by experienced and highly trained engineers using industry standard tools and 100 OEM parts. You need a screw driver to fix the pliers of the seat belt retractor.

To start with locate the cover of the retractor. The cover is a small door and is located below the shoulder mount of the seat belt. You need to remove the mounting screws in the cover.

Reinstall the 14mm bolt. It also helps to clean the belt itself. To clean the belt remove the belt completely and wash it in a washing machine.

Simply remove the belt from the retractor and then remove the other 2 14mm bolts that anchor the belt down. Place the tongue of the seat belt into the belt buckle until you hear a clicking sound indicating the belt is locked in place. Step 2 Pull down on the top portion of the seat belt until the webbing of the belt has been completely pulled from the retractor located in the door frame.

This releases the locking mechanism in the retractor. Because the seat belt has to be in the fixed position and angle in order to retract we have a certain length of the webbing out to make the installation process more manageable. Once the seat belt is bolted down you may cut the zip tie and enjoy the smooth retraction of your repaired seat belt.