How to install a rubber grommet

Slide a wood block under the tarp mark and align the hole cutter over the mark. Measure the object that you are willing to permit through the grommet as well as the thickness.

Align the setter or punch over the top of the post side of the grommet the back side of the fabric.

How to install a rubber grommet. If youre having trouble bending the grommet try boiling it. Letting a rubber grommet sit in boiling water for a few. If the fit is a bit tight an easy way to install the rubber grommet is to use silicone applied around the outside of.

First try and fit one side of the grommet flange into the opening. Push in part of the flange and manipulate it around the edges. Since rubber is flexible it helps if you bend the grommet as you fit it in.

Use a plastic putty knife to push it completely into the opening. You can then insert the necessary item through the grommet hole. Steps to install rubber Grommet 1 Select the accurate grommet.

The instrument may be wood or metal needs grommet to be placed over all the sharp. 2 Measure it properly. Measure the object that you are willing to permit through the grommet as well as the thickness.

3 Put one side of one. Grommet Installation Made Easy Step 1. Measure for the HoleMeasure where you want the center of the grommet and mark the cloth with a pencil.

Insert the Tall Half Step 3. First off try to fit one side of the grommet before manipulating it around the edges so that the other one can fit. This is why we said that the hole should be smaller than the grommet but not by a lot.

To help you push the grommet even further into the hole you can use a simple knife. Push one side of one rubber grommet edge into the opening to begin inserting the grommet. Manipulate around all of the edges to insert the grommet.

It is okay to bend the rubber grommet as necessary when working the grommet into the opening. Insert whatever wiring or tubing you are placing through the grommet through the hole of the grommet. When assembling first mount on both sides of the grommet and once you have done so you can manipulate the other parts as rubber is known to be very flexible.

This makes the work easier since you do not have to bend the rubber groove to mount it. GW - Rubber Grommet Groove Width should approximately match the thickness of the installation wall. GD - Rubber Grommet Groove Diameter GD should approximately match the installation hole size.

OD ID and TK dimensions are typically less critical depending on the application. Position and mark the inside of eyelet on your project. Insert the eyelet barrel in hole from the RIGHT side to the WRONG side of fabric.

Place washer over barrel of eyelet. Place anvil on a very hard surface like the floor. Place eyelet in anvil grab.

When installing a rubber grommet some objects might be difficult to insert. You might have to slit one side of the grommet with a razor blade or sharp knife. When this is done you then wrap the rubber grommet around the wire and you use silicone sealant to ensure that it is firm.

Splice the pigtail supplied in the lamp kit to the wires for the original lamp. You can use solderless butt connectors for this splice. Feed the pigtail out through the back of the grommet and plug it on to the connector on the lamp.

Carefully align the male connector to the female terminal on the lamp and push firmly together. Using a hammer pound the hole cutter making sure the wooden block is securely under the tarp until the hole is formed. Setting the Grommet.

Using an anvil set the grommet and push the end post up through the tarp. Then slide a washer down the post so that the tarp is now between the grommet and washer. Place the grommet pliers which look much like a hole punch over the mark for the intended hole.

Place the bottom half the grommet open side up on the bottom holder surface of the pliers. Step 3 Place the top half of the grommet open side down centered over the hole mark. Put the anvil under the front of your grommet the right side of the fabric.

Align the setter or punch over the top of the post side of the grommet the back side of the fabric. Now using your hammer or mallet pound on the setter in smooth strong strokes to attach the two grommet pieces together. Mark the desired location of the grommet.

Slide a wood block under the tarp mark and align the hole cutter over the mark. Strike the hole cutter sharply with a hammer until it punches through the tarp. Grommet kits include an assortment of grommets in several sizes and all the installation tools required.

First it lubricates the rubber making it easier to install on the canopy. Flexing the rubber grommet also makes it more pliable and easier to work with. Lastly the petroleum jelly moistens the rubber to keep it from drying out with age.

I then use a blunt object such as a hex driver to force the rubber grommet into the mounting hole.