How to install exhaust wrap

Having problems wrapping your exhaust pipes. We used Thermalvelocitycouk Magma Wrap.

While wrapping the muffler try to ensure that the wraps are as tight as you can get them to be.

How to install exhaust wrap. Having problems wrapping your exhaust pipes. Watch this video to see how Alex does it. There is a little information provided about exhaust wraps in general.

How to Install Exhaust Wrap Header Wrap 1. Wear safety glasses gloves and dust mask when wrapping your headers. Youll want to avoid contact of the header.

Keep in mind that wrapping headers and exhaust pipes requires patience. Going slow and taking your time will help to. This step is.

Installing the wrap is the trickiest part especially in the tight bends. There are few tricks to make this easier as we have illustrated below. We took a set of custom-made headers and a downpipe for a turbo engine to show you the process of installing exhaust wrap.

Once you get the first piece done the next one is that much easier. Get your exhaust pipe wrap here. This video shows how to wrap exhaust headers.

There are a few different applications of exhaust header wrap but the principals are pretty much the same and. In this video we show how to properly wrap exhaust headers. We used Thermalvelocitycouk Magma Wrap.

We strongly recommend checking them out unmatched qual. Take out the wrap from the packaging. Use the exhaust wrap calculator in the Tech section of our website to make sure.

You may soak the wrap in water first to make easier to wrap the pipe tightly but this is not necessary. Start by wrapping the desired pipe with about ½ overlap. The best pro tip we can give on how to install exhaust wrap is this.

After wrapping 12-18 inches of your exhaust or header pipe go back and grab the wrap and twist it tightly onto the pipe. If you soaked your wrap you will actually see water drip like wringing a sponge when you twist and tighten. Wire down one end of the wrap at the exhaust outlet and start wrapping pulling the wrap tight and overlapping the preceding layer roughly halfway with each wrap.

Draw the wrap as snug as you can to eliminate wrinkles and ensure it doesnt loosen up over time. A small screwdriver can be used to gently pry the pipes slightly apart so that the wrap can pass through and around. Some exhaust wraps must be soaked in water before installation.

Lava Wrap needs only a spritz of water from a spray bottle to lightly wet the wrap. Start an initial wrap around around the primary tube at the exhaust port closest to the engine and secure it with a stainless steel tie or a hose clamp. Continue wrapping using 14 overlap with each pass.

Keep tension on your wrap and use your hands every two to three coils to tighten the wrap. Decide Whether To Wrap Your Bikes Exhaust. Why wrap exhaust pipes.

Before tearing your bike apart you must be certain that wrapping its exhaust is the right thing to do. Simply put there is a lot of misinformation about pipe wraps. First you should understand than an exhaust repair wrap probably wont improve performance.

Put on your glasses dust mask and gloves. Clean exhaust system - clean headers exhaust pipes mufflers from grease and dirt. Failure to do so may result in a fire.

Start by folding back the end of the exhaust wrap by 341. Make sure you tuck the fold end under the exhaust wrap and place on the pipe. Begin to wrap tightly around the exhaust piece while pulling on the wrap itself.

Make sure to keep the wrap tight Use Zipties to keep the wrap in place as you pull the exhaust wrap tightly Remember to continually pull on the wrap to keep it tight. Install Exhaust Wrap Slowly start applying the wrap all around the exterior of your bikes exhaust pipe. As you wrap the pipe you should overlap any previously-wrapped section by 3 or 4 inches.

While wrapping the muffler try to ensure that the wraps are as tight as you can get them to be. Tape Another issue with headers is the intersections of pipes. You cant wrap a header or manifold with a single piece of wrap you need to wrap each smaller tube and then wrap the larger tube to incorporate the wrap over the smaller pipes.

Tape keeps the wrap secure until you get the overwrap complete.