How to polish atv plastic

Works as a polish undercoat protector and even as a light lubricant. For the best results continue to polish the plastic using circular motions.

Supplied in the kit are three different grits of sandpaper.

How to polish atv plastic. The plastics on my Yamaha Kodiak ATV were faded and oxidized. I searched the web and a 6040 paint thinner to boiled linseed oil mix seemed to get good revie. How do you paint an ATV.

The key to successfully painting ATV and dirt bike plastics is proper preparation. Using these procedures you will be able to prepare your ATV and dirt bike plastic for painting. It goes without saying that the first step is to clean the plastic.

Once this is done sand the entire surface with 180 grit sandpaper. Pre-mix in a container or spray bottle 3 parts boiled linseed oil to 2 parts paint thinner. Pour some of the mixture onto your plastics or on a rag and wipe along the surface.

It will be a bit runny so make. Let the mixture sit for about 20-30 minutes in the sun. The heat will open up.

Starting with the front and rear racks removed we gathered the water hose a bucket and our 20 Plastic Renew. Wash your ATV with soap and water to remove any dirt or grease from the surface. Its a 1 to 1 ratio and comes out at the same time.

Mix it together and fill the deep scratches with it. The stuff sets in about 15 20 mins and you can sand it down after a half hour. If you use a putty knife to clean off the excess after filling the scratch it makes the sanding after much easier.

Finish off with 0000 steel wool. If you dont have much oxidation or scratches you can just scuff up the plastic with the super fine grit and the steel wool. I used a Dremel oscillating tool to sand most the plastic.

I had to make my own triangles of the proper sandpaper because I couldnt find any locally. 320 was the finest grit I could find. Once dry use a silicone spray polish on all plastic and follow-up with a microfiber cloth to help keep dirt and debris from sticking - this makes it easier to wash after the next ride.

The silicone spray also gives that brand new looking shine youre after. Finally lube up your chain and put in a new air filter if needed. Step 1 Clean the plastic.

Take a clean damp cloth and dip it into some warm soapy water. Gently rub it in a circular motion all around the scratch. This will remove any dirt and grease making it easier to get rid of the scratch.

Dry the area with a clean dry cloth when youre done1 X Research sourceStep 2 Run a fingernail over the scratch to check its depth. Shallow scratches can often be buffed out. Run your fingernail across the scratch.

If it catches in the groove then. Provides a fresh and clean detailer to restore the factory shine. Works as a polish undercoat protector and even as a light lubricant.

Repels water and dries completely. Easy to use application. Works on all Motorcycle and ATV plastics.

Gives your bike a showroom shine. For factory or aftermarket plastic - all colors all makes. With the recon that I have.

The plastics were faded. I worked in a body shop for years when I was young. I was always the guy they trusted to water sand and buff out paint without burning the paint on the car.

So I tried to water sand the plastics on the recon with 1500 grit water sand paper and did so. Once you have pre-soaked your ATV and have loosened up all of that caked on mud its time to forcefully blast the mud off. The easiest and most thorough way to do this is with a pressure washer.

Gas-powered washers are the most powerful but even electric pressure washers work better than a hose and a nozzle. Not only should you learn how to clean your ATV plastic but you should also learn how to clean AND polish ATV plastic. Once the cleaning is done get a dry towel and dry all parts of the plastic exterior.

After that you can use some automotive wax to give it a little shine. Rub the polish into the plastic. Use a microfiber cloth to even out the coating and work it into the plastic.

For the best results continue to polish the plastic using circular motions. When youre finished the plastic should shine and look much better than when you started. Cut a piece of 200-grit wetdry adhesive sandpaper to fit a circular foam sanding pad.

Adhere the paper to the pad. Dip the pad in your bucket of water or spray both the paper and the plastic surface you are sanding with the spray bottle. Supplied in the kit are three different grits of sandpaper.

Start with the 220 dip it in water and do light even sanding coats. STEP 4 Move on to the 320 grit and do the same smoothing the plastic out with the lighter-grit paper. In many cases you can use the same gentle automotive detergentbike wash for plastic parts as for other parts of the UTV.

Special-purpose plastic cleaners are also available. A plastic polish at the end brings out that just-like-new shine while silicone sprays can minimize mud adherence on your next trail ride.