14
Oct
Depending on the application your serpentine belt will either have. Inspecting your belt for signs.
Then release the tension on the tensioner and remove the wrench.
How to put serpentine belt on. There are three types of belt tensioners used for serpentine belt systems. All of them involve a pulley. The first type is tightened or loosened via a regular hexagonal bolt on the face of the pulley.
This is also the most common these days. Relieving the Tension on the Serpentine Belt 1. Determine if there is a belt tensioner pulley.
Depending on the application your serpentine belt will either have. Use a wrench to relieve the auto tensioner. Auto tensioners have either a hole that will fit a half inch drive.
Most of the serpentine-belt installations use a spring-loaded tensioner pulley that keeps a constant preload on the belt eliminating the need to adjust the tension. How to Put a Serpentine Belt on a Car - Step-By-Step First closely examine the path that the old belt follows around each pulley. If you need to create a diagram that.
Insert a 38-inch ratchet into the hole in the tensioner arm. Youll need an extension to reach inside the hole. Install the new belt Replacing the serpentine belt is as simple as threading it into position cranking the tensioner and slipping the belt over the tensioner pulley or nearest pulley up top.
Belt tensioners are mostly spring tension. Once installed the spring retains pressure to the belt. Using the serp belt placement tool route the new belt around the belt path.
Rotate the tensioner again while you load the belt around it. Wrap the new belt around the crankshaft pulley then around the grooved pulleys. Finish the job by sliding the belt onto a rounded non-grooved roller.
Once again put the 14mm wrench on the tensioner pulley then pull the wrench toward the front of the car to release the tension. Reach under the tensioner pulley and slide the belt onto the idler pulley. Then release the tension on the tensioner and remove the wrench.
If the serpentine belt goes you are done until you get a new one. This is where preventative maintenance is your friend. You need to know the signs of a bad serpentine belt and the steps for serpentine belt replacement.
Serpentine Belt Failure Warning Signs. Noise A worn serpentine belt can start slipping. Serpentine Belt is a critical accessory in the engine system of a vehicle.
It drives the parts of a vehicle which are responsible for vehicle movement on the road. Power steering water pump and air-conditioner are some of the main parts which run in the car with the help of a serpentine belt. Open the hood and inspect the serpentine belt for wear and damage and its tension.
If the belt seems fine start the engine and squirt the ribbed side of the belt with some water. Listen to the sound. The noise will identify if it is the belt tension a misaligned pulley or a failing pump or motor.
Make a note of how the main serpentine belt on your Kia Sedona winds around each of the pulleys so you can put it back the same way. Step 6 Locate the tensioner pulley and adjustment bolt from under the wheel well in the center of the engine facing the passenger side of the vehicle. The serpentine belt on a Kia transmits the torque energy from the crankshaft out to the various engine accessories.
As the crankshaft pulley turns it moves the serpentine belt which then spins the other pulleys. Over time the belt begins to stretch crack fray and ultimately break. Inspecting your belt for signs.
See all 29 photos Installing the six-rib serpentine belt puts a bow on the accessory drive installation. Notice how low and tight everything mounts against the block an important feature in a hot. Replacing a Serpentine Belt - EricTheCarGuyIve had more than one request for this the other day I had one come in and was happy to make the video for it.
Sometimes the belt is torn because of the abrasiveness of the pulley flange. Car experts advise on smoothing its edges in order to prolong the serpentine belts performance. Clear Grit And Debris.
In most cases serpentine belts malfunction due to the accumulation of dirt around the areas between the belt and the pulley. This is a video tutroial on how to replace the serpentine belt for a Ford F150 54L V8. To guide the belt into and out of its engagement position you have to turn it almost perpendicular to the pulley.
Once you get it through the space however youre home free. And so we went on.