01
Nov
Remove the draglink using a ball joint remover device. If the new Pitman is in or youre not doing that job today go ahead and finish up the idler arm.
How to Replace the Pitman Arm in a Chevy Truck Step 1.
How to replace a pitman arm. How To Replace Your Pitman Arm or Steering Arm 01. Signs of this are your steering wheel moving 2 inches or more from side to side without turning the wheels at all. Be sure you have all your tools for replacing the Pitman arm before you start.
Its tough to go to the auto store. Take a new cotter pin and cut it to the size of the cotter pin you removed previously with the old pitman arm or about 14-12 longer than the castle nut. Thread the new cotter pin through the castle nut and twist the ends outward to keep it in place.
Reinstall the tire you removed in Step 1 of Part 1. How To Remove A Pitman Arm. How To replace A Pitman Arm.
How to change remove install a pitman arm. Chevy chevrolet pontiac oldsmobile gto chrysler dodge. How to Replace the Pitman Arm in a Chevy Truck Step 1.
Lift up the front of the vehicle using the jack and secure it on jack stands. Make sure the vehicle is. Locate the steering gear box on the truck.
Its on the drivers side frame rail and has a dog-legged arm that. How to Replace a Pitman Arm Shaft Seal Step 1. Raise and secure the vehicle.
Park your vehicle on level ground. Locate the tire next to the steering box front. Locate the steering box.
Looking under the vehicle find the steering linkage and narrow in on the steering box. How to Replace a Pitman Arm Shaft Seal Step 1. Raise and secure the vehicle.
Park your vehicle on level ground. Locate the tire next to the steering box front. Locate the steering box.
Looking under the vehicle find the steering linkage and narrow in on the steering box. Symptoms of a Bad or Failing Pitman Arm. If you notice your steering has lots of play while you are driving such as the wheel turns more than it should before the wheels.
Wandering to the left or right while on the road. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Remove the draglink using a ball joint remover device.
Remove the retainer bolt. Apply grease to the face of the sector shaft and position the pitman arm puller on the center line of the sector shaft. Tighten puller bolt a tap with a hammer on the pitman arm may be required to release the tapers.
Pitman arm puller used httpsamznto2LaLSmiChanging the wearable pitman arm on a 2WD 88-98 Style GMT 400 GMC Sierra Chevrolet Silverado. Pitman arm replacement can be physically demanding but with the proper pullers and separators the job is quick and smooth. First the wheels should be steered straight ahead and the steering wheel should be centered.
Then the pitman arm can be separated from the centrelink with a ball joint separator after the retaining nut is removed. If the new Pitman is in or youre not doing that job today go ahead and finish up the idler arm. Prepare a new cotter pin to match the one you removed by trimming it with the diagonal pliers so that both the long and short end match the pin you removed.
Place the idler arms bolt in the centerline. 1 Idler Arm 1 Idler Arm Bracket 1 Pitman Arm 2 Sway Bar Links 4 Ball Joints and 4 Tie Rod Ends Warranty. 1-year Replacement unlimited-mileage warranty Quantity Sold.
Set of 13 Prop 65 Warning. This product can expose you to chemicals including Lead and Mineral Oils which are known to the State of California to cause cancer and birth defects or other. Although it will take some time and effort it is possible for you to replace your own pitman arm assembly.
A specialty tool called a pitman arm puller will make this process a little easier. To replace the pitman arm youll have to raise the front end onto jack stands and remove the pitman arm from the steering gearbox using the pitman arm puller. Then fit the Pitman arm puller around the shaft end of the Pitman arm.
Use either a box wrench or a socket wrench to tighten the Pitman arm pullers jack screw against the Pitman shafts edge. Using a solvent and a shop rag clean the areas surrounding the Pitman shaft and the C-shaped retaining ring that puts the metal washers and.