04
Sep
Once you noticed that theres a constant connection between the positive end and the trickle charger you can now connect the negative cable. Check the switches and buttons on the charger box and set them prior to connecting the charger to a power source.
These chargers can be left connected to a car battery for long periods of time without overcharging.
How to trickle charge a battery. A trickle charger charges a car battery with a very low amperage. These chargers can be left connected to a car battery for long periods of time without overcharging. Charging at too fast of a rate or overcharging can cause damage to the battery.
Using a trickle charger is very easy. Most trickle chargers consist of a simple box where the guts of the charger reside a power cable and two alligator clips. Before connecting everything be sure to set the voltage and amperage appropriate for your battery.
Check the switches and buttons on the charger box and set them prior to connecting the charger to a power source. Ensure Battery Is Ready for Charging. You will see two alligator clips on the charging end of the trickle charger.
Attach the red clip to the battery positive terminal and attach the blue on with the designated negative connection you selected from the previous step. Keep the wires apart. Some people are foolish enough to turn the electricity on before plunging the cable to the battery.
Steps on how to trickle charge your dead battery. Park the car in a safe place. Before you start charging make sure that you are in a safe place away from people.
Charging could emit hydrogen. It may not be harmful to humans when breathed but it could cause an explosion. This should be taken carefully.
How to Use a Trickle Charger Step 1. Prepare the Battery for Charging. Keep in mind that excess hydrogen may become concentrated in an enclosed.
Choose a Suitable Ground Location. The next step is to select a good location for attaching the negative. How To Recharge A Car Battery Using A Trickle Or Speed Charger Step 1.
Put the battery charger on a firm surface but not on the battery itself. Place it at a distance depending on how long the charger cables are. Use the entire cable length to separate the charger from the battery as much as possible.
One should be a black clip and the other is a red clip. The red is for the positive end. Once it is attached to the positive end it should start charging.
Once you noticed that theres a constant connection between the positive end and the trickle charger you can now connect the negative cable. Trickle Chargers as Compared to Other Charge Methods If you already have a standard battery charger you may be wondering why you cant just go ahead and use that to keep. Jumping your battery to get it started is actually the hardest on its integrity so its something to refrain from.
Trickle chargers are mainly used to maintain your charge on your battery over a period of time so that it never runs out of charge and you are never left stranded with a flat battery. It takes a long time to charge and will switch off automatically in some chargers once your battery is fully charged. You simply connect the charger to the terminals plug the charger in and you can walk away from it for months and your battery will be taken care of without fear of a dead battery from overcharging.
I havent found a charger that is more gentle on a battery than this one and it will not cause them to sound like theyre boiling from my experience from overcharging like a lot of other chargers on the market. How to Trickle Charge a Car Battery Step 1. Open the batterys vent caps to check the electrolyte level in each cell.
Add distilled water to the bring the. Use a trickle charger that matches your batterys voltage output. Most cars use 12-volt batteries but check the.
Although they work differently setting up battery conditioners and trickle chargers are virtually the same. Make sure your car is parked in a well-ventilated environment turn off the ignition and remove the key. Select the appropriate power settings for your battery using the devices controls.
Dig up a large bolt which is connected or attached to the engine block or chassis. For the alternative you can get a portion of the frame which is free from oil grime and dirt. Also never use the negative terminal of the battery because it can be the cause of unexpected fire or exploitation.
Attach the Cables Step-3. Be sure to connect the negative black clip to the negative ungrounded battery post first. Once that connection is made connect the positive red to the positive battery post.
Be sure you do not reverse polarity. Once both connections are properly made plug in your charger and turn it on. Trickle chargers work by releasing a small amount of current to match a batterys natural self-discharge rate to keep it topped up at its fully charged level.
These products can be used on your car. A trickle charger is just one tool you can use to maintain your vehicles battery life. To ensure you dont end up stranded on the road or lake you can also follow these steps.
Store your battery or vehicle in a cool location protected from extreme temperatures and changes. Use a battery with the correct amperage needed for your vehicle. Attach the negative clamp to a grounded point on the vehicles chassis.
This will typically be black and marked with a minus sign -. Turn on the battery charger and begin the charge. When the charge is finished turn off or unplug the charger and remove the clamps in reverse order black first then red.