How to use a tyre pressure gauge

Tyre pressure is usually measured in kilopascals kPa or pounds per square inch psi. Most will display air pressure in psi kPa kilopascal or bar barometric or 100 kPa.

Fill up the tire by pressing the air compressor nozzle onto the tire air valve in the same manner as the gauge hard and straight-on to create a tight seal.

How to use a tyre pressure gauge. CHECKING THE TIRE AIR PRESSURE USING A PRESSURE GAUGE DEVICE Take the cap of the tire valve. To do this you need to unscrew the valve stem or the black extension near the hubcap. As to how to connect the instrument to the tire may slightly vary depending on what type of gauge.

How to Use a Tire Pressure Gauge. Checking your tire pressure is a breeze. First you should only check your tire pressure when the tires are cold.

That means your car should be parked for at least three hours. Then find out what your tire pressure should be. Only 25 percent of drivers use the correct method to determine tire pressure.

Some people look at a tire pressure chart or eyeball the tires and guess what the pressure should be. This is a video on how to check your cars tire pressure using three different types of pressure gauges. We use a stick type pressure gauge a dial pressure.

How to Check Tire Pressure and Inflate Tires - as part of the expert series by GeoBeats. Filling tire pressure is a pretty simple process. Simply remove the valve cap and attach the tyre pressure gauge to the tyre.

Make sure the gauge is attached evenly and securely. The gauge will display the PSI for each tyre. You can now refer back to the manufacturers recommendations to interpret whether the tyre is under-inflated over-inflated or just right.

How to Check Tire Presure. Start with Cold Tires if Possible. Vehicle manufacturers specify PSI literally pounds per square inch of pressure assuming tires are cold.

Check the Manufacturers Recommended PSI. Write Down the PSI for Each Tire. Check Tire Pressure with Your Gauge.

There are three simple steps involved in measuring a tire s pressure with a pressure gauge. Get in a steady position to apply the pressure gauge to the valve stem. Apply the gauge forming a good seal between the gauge and the stem and releasing air from the tire into the gauge.

Fill up the tire by pressing the air compressor nozzle onto the tire air valve in the same manner as the gauge hard and straight-on to create a tight seal. Hold the nozzle onto the tire air valve for about 30 seconds to one minute depending on how low the initial reading is. Repeat Step Three to get the new reading.

Then press the air pressure gauge into the valve stem evenly to inflate the gas. Record the reading of the gas valve. You may find a hissing sound that indicates the pressure gauge isnt attached to the valve tightly.

So it wont provide you an actual reading. Reopen the pressure gauge and press it again into the valve. Once youve got a suitable pressure gauge.

Remove the valve dust cap from the tyre valve and place the pressure gauge onto the tyre valve stem Press down the gauge evenly on the valve stem to ensure you get an accurate reading Check the reading on the pressure gauge to determine if youll need to. First find this range before using a gauge or inflating. Once you know the psi range use your tire gauge by placing it on the valve and pressing down causing the needle on the gauge to move and display the pressure.

Alternate between the air pump and gauge until you reach desired pressure. To make things easier get a pump with a built in gauge. Insert the pressure gauge and press it down into the valve.

Turn the pressure gauge on and place the opening at the end of the hose on top of the air valve. Push the hose in to open your air valve and connect the compressor or gauge. As you press the hose into the valve youll hear some air escaping.

Unscrew the cap on the air valve of your tyre. Push your tyre pressure gauge firmly onto the tyre valve. Look at the pressure reading on the gauge.

If the reading is low attach the air hose to the tyre valve and increase the pressure to the correct level rechecking with your own gauge if necessary. Screw the cap back onto the tyre air valve. Tyre pressure is usually measured in kilopascals kPa or pounds per square inch psi.

Keep your tyres inflated to the pressure recommended by the car manufacturer. This is often found on a sticker inside the drivers door frame in the glove box or on the petrol tank flap. Check when tyres are cold.

Digital gauges are the most accurate and very easy to read. Most will display air pressure in psi kPa kilopascal or bar barometric or 100 kPa. Once the tire gauge is pressed on to the valve.

Having an easy-to-read tire pressure gauge is key to setting up your tire pressure. A lot of pumps will have built-in gauges. There is a chance these gauges are a bit inaccurate.

If you suspect yours is off that is fine as long as you know what to expect and are consistent in checking your tires before each ride. The easiest method is to use a tire pressure gauge that you can purchase online or at any automotive parts store for cheap. Its normally recommended to check your cars tire pressure levels when.

In order to check your bikes tire pressure with a Presta valve you can use a pump with a gauge. First unscrew the valve nut on its tip. To make sure it is correctly done apply some pressure with the tip of your finger.

Air should flow out of the tire and seal back again once you stop pressing.